knife edge

英 [ˈnaɪf edʒ]

美 [ˈnaɪf edʒ]

adj.  形势难料的

机械

英英释义

noun

• the sharp cutting side of the blade of a knife
  Synonym:cutting edge

双语例句

• This time, United face Chelsea in a potential Barclays Premier League title-decider at Old Trafford on Saturday with the championship still on a knife edge and a run-in laden with pitfalls to come.
  这次，曼联周末就将在主场迎战切尔西。这很可能将决定本赛季联赛桂冠的归属，卫冕冠军现在的领先优势并不大。而现在又折损大将。
• Study of rotating soft knife edge wavefront sensor used in adaptive optics
  一种适于自适应光学的旋转软刀口波面传感器的研究
• Two series of fatigue crack growth rate ( FCGR) tests using three point bend specimen with different integral knife edge designs are performed. Effect of elastic modulus on the measurement of fatigue crack length using compliance technique is analyzed.
  用不同整体刀口设计的三点弯曲SE（B）试样做了两组疲劳裂纹扩展速率（FCGR）试验，分析了弹性模量在柔度法测量疲劳裂纹长度中的影响。
• Beam quality factor M~ 2 is measured by the means of knife edge for different bending of LMA fiber and the slope efficiency is measured separately.
  采用刀口法测量了不同弯曲直径下的激光光束质量因子M~2，并对每种情况下光纤激光器的斜率效率进行了测量。
• The secret of successfully pressed hems is to use very little pressure so that the edge is not flattened to produce a knife edge.
  成功熨烫底边的窍门是用很小的压力，这样就不会倒伏而产生一条刃形边缘。
• On the basis of testing results, main cutting curves of wheat straw were given, under different cutting speeds of rotatory blade with different straw lengths, moisture centents cutting positions, different thicks knife edge, with and without shear bar.
  得出粉碎刀片在不同切割速度下，对短秆、长秆、秸秆不同切割部位、秸秆不同含水率、不同刀刃厚度、有定刀和无定刀等情况下的切断率曲线。
• If you don't do this, the plane will fall off into a knife edge spin.
  假如你做得不好的话，飞机会进入刀刃旋转。
• In this paper, the parameters of the cylinder-type forage cutterhead with straight knife edge is analysed, the mathematical formulas concerned have been derived. The cutterhead ZC-1.0 is discussed as an example.
  本文对直刀刃滚刀式饲草切碎器的参数进行了分析，推导出了有关数学式，以ZC-1.0型切碎器为例作出了评论；
• This text has mainly proposed some discussion opinions on this processing method, explained its processing principle, set up mathematics model, proposed optimizing the design prospect of the excellent horn of knife edge to the improvement of the machining accuracy of the whorl finally.
  本文主要是对该加工方法提出了一些探讨性见解，并阐述了其加工原理、建立了数学模型，最后对螺纹加工精度的提高提出了优化刀刃优角的设计展望。
• The concept of a new type wavefront sensor-rotating soft knife edge wavefront sensor has been proved with Fourier optics theory.
  利用傅里叶光学理论，证明了一种新型波面传感器&旋转软刀口波面传感器的概念。